Full remodel in maple and cream
Pickled oak and brown granite replaced entirely — new light maple cabinetry, new flooring, and a long cream quartz island with seating.
- Material
- Cream quartz
- Service
- Countertop Fabrication
- Completed
- June 2026
The largest job on this page. The kitchen that came out was pickled oak with a brown granite peninsula and a bulkhead cutting the ceiling in half; the kitchen that went in is light maple, floor to ceiling, with a single long island in place of the old peninsula.
The counter is a cream quartz with a soft clouded movement rather than a vein — a hard white would have gone cold against maple this light. The island runs long enough to seat three on the open side and still leave a full prep run, which is the thing the old layout could not do.
Before and after
Walkthrough
On the job
New maple cabinets and cream quartz turning the corner beside the refrigerator 
The finished range wall, cream quartz either side of a stainless slide-in range 
Before: the old granite counters at the sink, pickled oak cabinets and a dark tile floor
The specification
What went in, in the owner’s own words on the job sheet.
| Detail | What we used |
|---|---|
| Completed | June 2026 |
| Material | Cream quartz |
| Service | Countertop Fabrication |
Town and month only — we do not publish a customer’s address.
About Cream quartz
This kitchen is topped in Cream quartz. We fabricate it in our own shop, which means the seams, the sink cutout and the edge are cut by the people who set the tops — not shipped in from a third-party shop that never sees the room.
- <a href="/countertops/">See the full countertop range →</a>
- <a href="/services/countertop-fabrication/">Countertop Fabrication — how the job runs →</a>
- <a href="/guides/">Homeowner guides on choosing and caring for stone →</a>
What a job this size runs
Our published installed-project ranges — the same in every town we serve.
| Kitchen size | Engineered Quartz | Granite | Quartzite | Marble |
|---|---|---|---|---|
| Galley kitchens (30–45 sqft) | $3,600–$6,750 | $4,200–$7,650 | $4,500–$8,550 | $5,100–$9,000 |
| Small kitchens (45–60 sqft) | $5,400–$9,000 | $6,300–$10,200 | $6,750–$11,400 | $7,650–$12,000 |
| Medium kitchens (60–75 sqft) | $7,200–$11,250 | $8,400–$12,750 | $9,000–$14,250 | $10,200–$15,000 |
| Large kitchens (75–90 sqft) | $9,000–$13,500 | $10,500–$15,300 | $11,250–$17,100 | $12,750–$18,000 |
| Extra large kitchens (90–120 sqft) | $10,800–$18,000 | $12,600–$20,400 | $13,500–$22,800 | $15,300–$24,000 |
Installed project ranges as of 2026-07 — template, fabrication and standard installation included. Your kitchen gets a firm number after a free in-home template.
Questions we got asked on this kind of job
Can I change my kitchen layout without moving the plumbing?
Often, yes - and it is the single biggest budget lever in a remodel. Keeping the sink, range, and refrigerator in place means new counters, backsplash, and cabinets go in without opening walls or floors, while relocating a sink across the room adds supply, drain, and vent runs, floor patching, and usually a plumbing permit. A practical middle path is sliding fixtures along the same wall a few feet, which reuses most of the rough-in. Decide the layout first, because it determines whether your budget is buying finishes or pipework.
Can I get new countertops without touching my cabinets, or will the swap wreck them?
Countertop-only replacement is one of the most routine jobs in remodeling, and sound cabinets survive it fine. The installer pries off the old tops, checks that the boxes are level and solid, shims where needed, and sets the new surface. The honest caveats: cabinets with swollen particleboard around the sink from years of small leaks may need repair first, old tile-over-mortar tops can be violent to remove, and you should expect some paint touch-up along the wall line where the old backsplash sat. A good fabricator flags all of this at the template visit, not on install day.
Can I install a tile backsplash myself?
Of the three projects, this is the most DIY-friendly: small area, no structural stakes, forgiving timeline. The skills that separate good from regrettable are layout planning around outlets and edges, straight cuts (rent a wet saw), consistent spacing, and clean grout work - and buy 10 to 15 percent extra tile for cuts and breakage. Professional labor runs roughly $5 to $20 per square foot if you decide midway that a flawless finish matters more than the savings.
Can I install my own backsplash, or should I hire a tile setter?
A straight running-bond or stacked ceramic backsplash is one of the most DIY-friendly tile jobs in a house - small format, no water exposure like a shower, and you save roughly $10-15 per square foot in labor. Hand it to a pro when the job involves glass tile (visible adhesive and cut edges), natural stone (sealing, blade chatter, breakage), herringbone or diagonal layouts (compounding alignment errors), large-format panels, or any slab product, which is fabricator work full stop. Whoever installs it, outlets are the tell: sloppy cuts around receptacles are the first thing a trained eye notices.
Want one like this?
Free in-home template, an honest number, and one crew from measure to install.
Ready for a real number?
Free in-home template and an honest quote — you keep your money until there's a countertop to trade it for.